How Does A Floor Spring Meet A Patch Fitting?

Publish Time: 2026-11-20     Origin: Site

On site, the two parts arrive separately and are installed by different trades. A floor spring is set into the ground and cemented before the glass is hung. A bottom patch fitting is already clamped to the door by the time the glass is lifted into place. Nothing connects them until the final step, when the door comes down and settles onto the spindle.

So the answer to the question is short. They meet once, at the bottom edge of the door, and everything the door does afterwards passes through that point: how it swings, where it stops, whether it stays quiet.

What makes the meeting worth a closer look is that the two parts are chosen by different rules, made to different drawings, and joined by a fit that no one can inspect once the door is hanging.

// Two Parts Installed Apart, Joined at One Point

A floor spring sits in a cement box cast into the floor, with its cover plate finished flush with the surrounding surface. The spindle rises near the end of the cover plate rather than in the middle, which is what allows a frameless door to pivot close to its edge.

A bottom patch fitting clamps the bottom edge of the glass door. It is a stainless cover over an aluminium core, tightened onto the glass through the drilled holes. The head sits inside it, facing down.

The order is fixed by the building, not by preference. The floor spring is set first, because the floor has to be finished around the cement box. The patch fitting goes on the door while the door is still flat, because it has to be clamped before the glass is lifted. Only then is the door hung and lowered, and the head comes down over the spindle.

The connection itself is a male-and-female fit. The spindle is a shaped post; the head carries a recess cut to receive it. There is no bracket and no adapter between them. The door's weight passes from the glass, through the patch fitting, into the head, and down the spindle, which is anchored in the floor.

// The Spindle Is Part of the Floor Spring

A floor spring is not a generic part with a standard connection point. The spindle is part of the model's design rather than an accessory added later, so the shape the door has to sit on comes with the floor spring, not with the fitting.

Across the market there is more than one spindle profile in use, and each profile has a corresponding head. A bottom patch fitting is therefore supplied to match the spindle it will sit on. The body stays the same across the range: the cover, the core, the bolt pattern through the glass. What changes is the head.

This is also why the bottom patch fitting is normally specified against the floor spring rather than on its own, even when they come from different suppliers. The specification starts from the model, and the head follows from it. Get the model right and the shape at the interface is right as well.

// Two Selection Rules, One Shared Shape

The two products are chosen by different numbers, and neither number tells you anything about the other.

A floor spring is selected on door weight and door width read together. A heavier leaf needs a higher rating; a wider leaf needs more resistance to twist as it swings. A door can sit inside the weight limit and still be too wide for the model, which is why the two figures are never treated separately.

A bottom patch fitting is selected on glass thickness, 8 to 12 mm, and on the finish. It carries no load rating of its own. It transfers whatever the door weighs into the spindle, and the floor spring decides whether that load is within range.

Decision

Floor spring

Bottom patch fitting

Selected on

Door weight and door width

Glass thickness, 8–12 mm

Rated for

Load and leaf width

No separate load rating

Sets the interface

Spindle profile

Head to match that spindle

The only thing the two selections share is the shape where they meet. Everything above that shape is glass, and everything below it is floor.

// The Risk Is Not the Shape, but the Fit

Because the head is matched to the spindle, the wrong shape is rarely the problem. The part arrives, it goes on, the door hangs. What decides how the pair behaves afterwards is not whether the head accepts the spindle, but how closely it holds it once it is on.

Two heads made to the same profile by two factories are the same shape on paper. They are not necessarily the same in the recess that receives the spindle, the wall thickness around it, or how deep the spindle sits inside it. A difference of a fraction of a millimetre is enough for the head to sit slightly loose on the spindle instead of being held by it.

A door with a loose head-to-spindle fit does not fall. It swings, it closes, it holds at 90 degrees. But under the weight of a moving leaf, the looseness allows a small movement before the head takes up against the spindle. That movement repeats every time the door passes the same position. In time it can produce a knock at the bottom of the door.

None of this is certain. Many installations that mix suppliers run quietly for years. The point is that this fit is internal: it sits inside two parts clamped together and closed from view, and no one will look at it again unless something goes wrong.

// Why a Click at the Bottom Takes So Long to Trace

A knock at the bottom of a glass door is hard to trace because the bottom of a glass door is busy. Within a hand's width there are the clamping bolts at the bottom edge, the head, the spindle, the cover plate and the cement box. The sound arrives at the floor, but it can start at any of them.

The usual route runs from the accessible to the concealed. The clamping bolts are checked first, because they can be reached with a wrench and they do come loose. The floor spring is checked next, since a worn seal or a low oil level will also make noise. Only after those are ruled out does attention turn to the fit between head and spindle, which cannot be seen with the door hung and cannot be measured without taking the door down.

That order is reasonable, and it is also why the search takes time. By the time anyone suspects the interface, the door has been worked on twice for other reasons, the bolts have been re-torqued, and the symptom has been described to two or three people who were not on site when it started.

There is a second reason. A loose fit at the spindle does not announce itself at every position. It tends to show up at one point in the swing, often near the closed position or at the 90-degree hold, and it may only appear when the door is moving at a particular speed. A fault that appears at one point in a cycle is harder to confirm than one that is present all the time.

A floor spring and a bottom patch fitting do not have to come from the same factory. The head profiles are not exclusive to one maker, and a buyer with an existing floor spring can source a matching part.

What same-factory supply buys is not a better product. It is one less variable. The spindle and the head are then made to the same drawing, checked against the same gauges, and held to the same tolerance band. When they meet, the fit is the fit the designer intended, rather than whatever two independent production lines happened to produce.

That is the whole argument, and it is a recommendation rather than a requirement. A mixed pair can be correct. It simply has one more thing that can differ, and the difference shows up where nobody can see it.

FAQ

(1) Does the floor spring model decide which head the patch fitting needs?

The model decides which spindle the door will sit on, and the head is matched to that spindle. That is why the model number is what a supplier works from: it identifies the profile the fitting has to receive.

(2) Why does a glass door click when it closes?

There are several possible sources within a small area: the clamping bolts at the bottom edge, the floor spring itself, or the fit between head and spindle. The interface is the least accessible of the three, which is why it is usually the last to be checked rather than the first.

(3) Does the load rating of the floor spring change the patch fitting?

Not directly. The floor spring is chosen on door weight and door width. The bottom patch fitting is chosen on glass thickness and finish, and it passes the door's load through to the spindle without a rating of its own.

(4) What glass thickness does a bottom patch fitting take?

8 to 12 mm. The holes in the glass are drilled before tempering, so the hardware and the hole positions are settled before the glass is ordered.

(5) Can the two be supplied in the same finish?

Yes. Both are available in satin, polish, gold and matte black. Jianlai supplies the floor spring and the bottom patch fitting in these finishes, so the two can be ordered to match at the door's bottom edge.

Two parts, installed on different days by different trades, meet at one point under the door and are never looked at again. Whether that meeting stays quiet is settled earlier, when the model was chosen and the head was matched to it.

Contact us

How Does A Floor Spring Meet A Patch Fitting?

What types of doors are compatible with floor springs?

Door Handles VS Knobs: Which Is The Better Option for Your Doors?

What Is A Patch Fitting And How Does It Work?

Shower Hinges for Small Bathrooms: Maximizing Space And Functionality